Blower Purge Heated Desiccant Air Dryers
A centrifugal blower and high efficiency heater elliminates the use for desiccant regeneration. The completely automatic drying system uses blower to pull ambient Air and pass it through the heater. This hot Air stream flows opposite to drying flow direction. Hot Air above 392°F regenerates the moisture inside desiccant bed and strips it completely of all moisture. The advanced control system monitors the dew point and adjusts the heating / regeneration accordingly thereby providing valuable energy savings.
Heatless Desiccant Air Dryers
Mikropor MHL Series Heatless Desiccant Air Dryers provide constant -40°F (standard) or -94°F (optional) pressure dewpoint. These dryers are designed to supply clean and very dry compressed air for critical applications.
Pre-filters and after-filters are standard on all MHL Series Heatless Air Dryers to keep the air stream clean and maintain the integrity of the desiccant medium. A very reliable electronic controller is incorporated so the dryer operates perfectly through the service life of the dryer. MHL Heatless Desiccant Dryers are equipped with robust valves and high quality desiccants in order to assure performance and provide the lowest pressure drops available in the market.
Mikropor Air Quality Focus
Mikropor knows the importance of high-quality compressed air and provides customers with the highest quality air possible. Using clean, dry air is extremely important for most air powered applications. Moisture or contamination in the air from the compressor discharge will result in many complications to production equipment. These complications will decrease productivity and may affect the production quality of final product.
Mikropor is aware of the importance of high quality compressed air and guarantees to provide customers with the highest quality of air. Using clean, dry air is extremely important for all kinds of air powered applications. Moisture or contamination in the air which will come from the standard compressor outlet will cause complicated system errors. These complications will decrease productivity and may affect the production quality of final products.
Compressed air entering the air net is always 100% saturated. When it cools, this moisture will condense, damaging your air system and niched products.
Remove moisture from compressed air with a dewpoint as low as +3°C/+37.4°F; Atlas Copco’s FD refrigerant dryers provide the clean, dry air you need to expand the life of your equipment and ensure the quality of your end product.
In addition, FD dryers comply with the most stringent environmental regulations.
The FX range of refrigerant dryers offers a reliable, cost-effective, and simple solution:
avoid condensation and therefore all chance of corrosion and damage. Compressed air needs to be dried, which is exactly what the FX units are designed to do.
These simple reliable units remove water from the air and the risk from your system, ensuring that your money doesn’t just disappear into the air!
Atlas Copco’s OSS offers absorption-based condensate management for oil-injected piston and rotary screw compressors below 30 l/s (60 cfm).
The oil-water separator uses a new, advanced filter medium to remove oil traces to concentrations below 15 ppm1.
The OSS is easy to install, use, and replace – the affordable condensate cleaning solution for smaller air systems.
Unlike currently available technologies, Nautilus filter technology allows significant improvements in energy efficiency, without any compromise on filter performance or reliability.
The first filters to make use of this innovative technology are Atlas Copco UD+ filters. These filters combine two filtration steps into one, meeting the high-quality requirements of diverse applications and providing significant benefits.
New additional to our G series and GO series, Mikropor “GON” series compressed air filters are designed for easy element replacement for “zero clearance” ability.
New additional to our G series, Mikropor “GO” series compressed air filters are designed for easy element replacement for “zero clearance” ability.
The Mikropor external drain is designed to remove liquid condensation from collection points in a Compressed Air System. The F series features a durable epoxy finish for corrosion resistance and ensures longer service life.
Mist Eliminators are designed to meet the demand for: Efficient removal of oil and mist carryover from piston or oil flooded rotary compressors.
50 bar Range made of Aluminum, No welding, strong and reliable design. 350 bar Range made of Steel. No welding, and very reliable for High Pressure appilications.
Find genuine Atlas Copco air compressor parts and accessories from Iacono, Inc. We are the sole distributor of Atlas Copco Air Compressors on Long Island and the NYC Metro Area.
Minimize downtime and maximize performance with equipment and parts you can rely on. Factors such as temperature and humidity are often outside of you control. By adding a compressed air dryer and filter to your system, you can make sure your production runs smoothly and free from overheating or contamination.
